Skin Talk: How To Rehead A Djembe

When you finish doing the weave and you have all the wrinkles out of the folds, you are ready to put the head on the drum. If there are more folds, you can always add more sinew to pull them out, or just pull them out by hand once you have the head on the drum (recommended). If you feel as if the rings will go too low, you can also take a piece of sinew and tie the weaves together in the center, pulling the skin tighter once you have started the head on the drum.

Putting The Head On The Drum

Depending on the thickness of your rings (some are more flexible than others) you can slip the flesh ring inside of the top ring without too much difficulty. If you’re unable to do it that way, go to plan B, which is to take just enough verticals to slip the flesh ring under the top ring from the side. Then lace the verticals back as far as you can without pulling the head tight.

Start pulling the verticals down from where the head is up the highest. You always want to pull the slack in the verticals, in the correct direction. When you tie the drum off through the end of the verticals with a loop, all the slack you pull will come through that loop. So the loop is basically stationary and the other end is where the slack goes.

Djembe Djembe

Some drums, such as those from the Ivory Coast, have a notch in the bottom for the ring to fit into. If this is the case, you do not have to worry about keeping the bottom ring level. Don’t pay attention to the next step (Keeping The Bottom Ring Level) if that is the case. You do not want to try and pull hard to start with. I will go around a wet head pulling verticals six times or more. This ensures (well, almost ensures) that the head will be level.

Keeping The Bottom Ring Level

The bottom ring also has to stay level, so you need to pay attention to it. It takes a fair amount of tightening to seat the bottom ring before it stops moving up. Then start pulling the verticals. Personally, I don’t use gloves when I do this, primarily because I don’t want to pull too hard. At this point you’re only trying to get the top ring level — not tight. You also have to keep the rings in the center of the drum. They have a tendency to move around a lot, so pay attention to them. When you have the top ring pulled down about level with the rim, turn the drum over to make sure that the bottom ring is level. By this time I put on gloves and pull fairly hard to get the bottom ring level. Switch back and forth checking the top and bottom rings to make sure they both stay level.

The final goal in pulling the verticals on a wet head is to have the top ring about .75" below the rim. It will go down further once it dries and then you really crank the verticals.

I usually stop pulling verticals when the ring is down .75" below the rim. Cut all the artificial sinew (if it wasn’t previously cut) to allow the head to go down further, and pull all the extra skin down the side of the drum. Use an Ace bandage to hold the skin that is hanging down, and cut off this extra skin after it has dried for a few days.

If you don’t hold the skin down when it dries, it will stick up and be in the way. The Ace bandage works well because it allows the skin underneath to dry along with the rest of the drum. Masking tape will also keep the skin down, but the skin under the tape stays wet longer.

A Close Shave

At this point you have a head that is fairly tight and soaking wet. It’s time for the dreaded shaving. Use a plain Bic razor. All you have to do is break the plastic guard off the front of the blade using a small set of needle-nose pliers, exposing the blade completely (be careful not to touch the blade when doing that). Then take a fine file, wet stone, or sandpaper and file the corners of the blade off at a 45-degree angle. This will prevent the blade from cutting into the head.

Shave in the direction that the hair lays (go with the flow, not against). Going against the grain will end up nicking the head. Keep the handle of the razor parallel to the surface of the head to keep the blade at almost a 90-degree angle to the surface of the drum — kind of like dragging the blade across as opposed to trying to slice the hair off.

Be careful along the rim of the drum. Use less pressure because it has a harder surface, and the blade will tend to scrape some of the top layer of skin off. You can press harder as you feel more comfortable. When shaving, start the blade above where you have already shaved, and be sure to use nice, even strokes.

After you’ve completed shaving, let the drum sit out in the sun for two days. Then wait an additional two to three days before pulling the verticals again.

And now … it’s time to play!

Page 3 of 3
Get the How To Tune Drums Minibook when you subscribe to our newsletter